文献类型：期刊文献

中文题名：基于裂尖等效塑性应变的面内与面外统一拘束参数的研究

英文题名：Study on the unified constraint parameter for characterizing in-plane and out-of-plane constraint based on the equivalent plastic strain

作者：杨杰[1];王国珍[1];轩福贞[1];涂善东[1]

机构：[1]华东理工大学机械与动力工程学院承压系统与安全教育部重点实验室,上海200237

年份：2013

卷号：36

期号：4

起止页码：222

中文期刊名：核技术

外文期刊名：Nuclear Techniques

收录：CSTPCD;;Scopus;北大核心:【北大核心2011】；CSCD:【CSCD2013_2014】；

语种：中文

中文关键词：面内拘束;面外拘束;裂尖等效塑性应变;GTN损伤模型;断裂韧性

外文关键词：In-plane constraint; Out-of-plane constraint; Crack-tip equivalent plastic strain; GTN damage model; Fracture toughness

摘要：为提高核电设备缺陷评定的准确性,需要考虑裂尖拘束对材料断裂韧性的影响。如何找出一个统一的参数以表征复合拘束,是目前断裂力学研究的主要问题之一。本文采用有限元模拟的方法,分析了εp等值线所围面积作为统一拘束参数的可行性。结果表明:εp等值线所围面积APEEQ与不同面内、面外拘束条件下材料的断裂韧性都有很好的关联性,因而它可能用来统一地表征复合拘束。用标准试样作参考,基于APEEQ定义了一个新的统一的拘束参数Ap。材料的标称化断裂韧性JIC/Jref与Ap呈直线关系,并与所选择的εp等值线无关。JIC/Jref-Ap直线关系对于材料是唯一的,不同材料的JIC/Jref-Ap直线斜率不同,斜率大的材料对拘束更敏感。该直线可能用于评价实际结构中不同拘束条件下裂纹缺陷的安全性。
Background： Constraint can significantly alter the material＇s fracture toughness. Purpose： In order to increase accuracy of the structural integrity assessment. It needs to consider the effect of constraint on the fracture toughness of nuclear power materials and structures. A unified measure which can reflect both in-plane and out-of-plane constraint is needed. Methods： In this paper, the finite element numerical simulation method was used, a unified measure and characterization parameter of in-plane and out-of-plane constraint based on crack-tip equivalent plastic strain have been investigated. Results： The results show that the area surrounded by ep isoline has a good relevance with the material＇s fracture toughness on different constraint conditions, so it may be a suitable parameter. Based on the area ApEEO, a unified constraint characterization parameter Ap is defined. It was found that there exists a sole linear relation between the normalized fracture toughness Jlc/Jref and √Ap- regardless of the in-plane, out-of-plane constraint and the selection of the cp isolines. The sole .JIC/Jref-√Ap line exists for a certain material. For different materials, the slope of JIC/Jref-√Ap reference line is different. The material whose slope is larger has a higher JIc/Jref and is more sensitive to constraint at the same magnitude of normalized unified parameter. Conclusions： The unified JIC/Jref-√Ap reference line may be used to assess the safety of a cracked component with any constraint levels regardless of in-plane or out-of-plane constraint or both.